Hi, today I tell you how to solve the Rubik’s cube.

So first, we how to learn a few moves

Here they are:-

 Step 1. Make a white cross.

1)Start by holding the cube with both hands with the yellow face on top and We will use the bottom layer with the white face.

2)Find these edge pieces with the following colors white red, white blue, white-orange, white green, and ignore those without white The diagram below indicates different situations find the matched case and execute the movement according to it, to put the white side next to the yellow center.

3)The side colors should match the color of the center.

We have to learn a few cases.

Here they are:-

Tips- 1)The gray represents the unnecessary part of the step.

2)The transcalent area represents the final position after executing the movement.

3)If there’s already a white edge on the top layer, hide it first and then keep solving the cross.

Doing this all step you will not find a white cross. Turn the top layer to match every cross piece one by one, turn 180° to matched down white center pieces. Repeat this step until all the cross pieces are in the right place.

Step 2-Solve the four corners.

1)Execute the right algorithm according to the situations shown in the diagram below.

2)Repeat this step until all four corners are solved.

3)Repeat this step until all four corners are solved.

4)The whole white side will solve.

Here are the cases you have to learn-

Tips:-If there are no white corner pieces in the top layer, then execute RU’R’ or RUR’. Like this case, the green orange white corner piece will place on the top side. After executing the algorithm, it could be solved by following the instruction

Step 3-Solve the four middle edge pieces

1)Find the edge which is not with yellow, and match its side color

2)Execute the right algorithm according to the situations shown in the diagram below.

3)Repeat this step until two layers will be solved.

4)The first two layers will be solved.

Here are the cases you have to learn-

Tips-1)If there are no right pieces in the top layer execute the above algorithms in this step, like (R’F’RU)(RU’R’F)

In this case, the green orange edge will replace by the top layer, and then follow the instruction to solve.

Step 4- Adjust the four top edges’ side

1)This step only requires the yellow side of the top, the other sides could be ignored.

2)There are only four cases in this step, which execute the Algorithm 6 once will you transform to the next case, until the yellow cross is done.

3)It will build up a yellow cross on the top layer.

Here are the cases you have to learn-

Step 5-Adjust the four top corners’ side

1)The diagram is a vertical view, and the yellow bars represent the vel low pieces on the sides.

2)Focus on the top side, and there are 7 cases for the total. The cases which only have one yellow corner on the top side just need to execute the algorithm once.

3)The whale yellow side will be salved.

Here are the cases you have to learn-

Tips-1)Make sure to adjust to the right position before executing the algorithm.

2)In Step4/5/7, if the first two layers were solved, the case is not included in the instruction, such as eight yellow pieces on the Cop side, or only two edges need to switch.

These situations indicate that the cube is assembled incorrectly, which has to reassemble to the solved state.

Step 6-Permute the four corners

1)Find the corners with the same color on the sides, and then execute Algorithm 9. If all the corners are placed correctly, then skip to Step 3.

2)If none of the corners are placed correctly, execute Algorithm 9 once, and look for a pair of the corner, then execute algorithm 9 once again.

3)Match the corners with the color of the first 2 layers by doing the U layer move.

4)All the corners will be solved

Here are the cases you have to learn-

Tips-1)The principle of Algorithm 9 is to exchange the position of the left and right rear comers.

2)Pay attention to the direction of L and L.

Step 7-Permute the four edges

1)The diagram is a vertical view. The arrows represent the moving direction of the edge pieces, and the black bars represent the same-colored pieces.

Here are the cases you have to learn-

Tips-1)M is the movement of middle layer.lt could be done by either index finger or ring finger pushing. M’could be done by ring finger move